Lx-300 manual

Why won't my product print serially from my computer? Can I use the platen knob to load or adjust paper? Copy or Print. Select the questions to view the answers Can I print on checks that are 3-inches in length? Error Messages or Lights.

Select the questions to view the answers Why is my product beeping three times and the Paper Out light is on? Select the questions to view the answers A label peeled off in the product. Paper or Media. Select the questions to view the answers Can I use the platen knob to load or adjust paper?

Print Quality or Appearance. Select the questions to view the answers When printing a multiple page document on single sheets, the first page prints correctly, but the pages after start printing too low. My product is not starting at the right position on the paper.

How can I change the top-of-form? Software or Setup. Select the questions to view the answers I'm printing serial, my baud rate is at , and intermittently my product will lose data. What driver should I use if my product is not listed? Encaixe a guia do papel, alinhando os entalhes em cada lado com as guias da impressora. Encaixe os suportes para papel. Montez le guide-papier, relevez-le et verrouillez-le en position. Inserte el cartucho de cinta hasta que encaje en su lugar.

Insert ribbon cartridge until it clicks in place. Guide ribbon between print head and ribbon guide. Make sure the orientation of the connector is correct before inserting it into the appropriate port.

Desligue a impressora. Turn printer off. Ajuste a guia de borda direita. Push paper release lever back. Slide the left edge guide to guide mark. Adjust the right edge guide. Each product marketed is identical to the representative unit tested and found to be compliant with the standards. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Desligue a impressora, retire a tampa da impressora e a guia do papel. Turn off printer; remove printer cover and paper guide. Pull paper release lever forward, and unlock tractor sprockets.

Cierre las cubiertas de las ruedas dentadas. Feche as coberturas das rodas dentadas. Deslize a roda dentada da direita e trave-a. Recoloque a guia do papel e a tampa da impressora. Close sprocket covers. Slide right sprocket and lock in place. Replace paper guide and printer cover. Fermez les couvercles de pignon. Faites glisser le pignon droit et verrouillez-le en position. The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment.

It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. This product is covered by a limited warranty. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation.

Differences in the Default Setting Mode. Printing a Self Test. Its faster, more reliable, and accommodates more copies per multi-part form 1 original plus 4 copies. It is backward compatible with the LX, so you should not have any problems using it with your current software. New Specifications This table summarizes the basic specification differences between the two models. Function Printing speed. LX NLQ 10 cpi : 44 cps uni-d Draft 10 cpi : cps High speed draft 10 cpi : not available High speed draft 12 cpi : not available.

You do not need to install this driver if you are happy with the driver s you are currently using for your LX If you decide to install the software, you can take advantage of the following features: A printer driver which lets you control printing.

The Status Monitor displays information about the printers status and lets you know if there is a problem with a print job.

This provides an alternative way to change the default settings as described on page Turning On the Printer The power switch has been moved to the side of the printer. The Control Panel The control panel has been modified, as shown on the next page.

It also loads continuous paper from the standby position or feeds it backward to the standby position; it replaces the Paper Park feature on the LX It still lets you select one of the printers built-in fonts through the Micro Adjust mode, as described on page 7 , plus it advances continuous paper to the tear-off position or feeds continuous paper backward to the top-of-form position. The control panel also features a Paper Out light to let you know when the printer has run out of paper or paper is not loaded correctly.

See page 7. Ejects a single sheet or advances continuous paper to the next top-of-form position when held down. Paper Out light On when no paper is loaded in the selected paper source or paper is not loaded correctly.

Flashes when paper has not been fully ejected or a paper jam has occurred. Feeds continuous paper backward from the tear-off position to the top-of-form position. Ejects a single sheet of paper. Loads continuous paper from the standby position. Feeds continuous paper backward to the standby position. Pause button Stops printing temporarily, and resumes printing when pressed again. When pressed for three seconds, turns on the Micro Adjust mode. Flashes when the printer is in Micro Adjust mode.

See page 8. The Tear Off lights turn on, off, or flash to indicate the selected font. Selecting Fonts On the LX you pressed the Font button to select one of the printers four built-in fonts. Hold down the Pause button for 3 seconds. Make sure the Pause light is flashing. Then press the Tear Off button to select one of the fonts listed in the table below. Continue pressing the Tear Off button until the lights indicate the one you want.

Then press the Pause button again to exit Micro Adjust mode. The selected font stays in effect until you change it again or turn off the printer. However, any font choices you make with your software will override your control panel selection. You will not notice any difference in printing unless you have specified margins in your software applications that are less than the minimum allowed by the LX 5.

In this case you may need to adjust your top and bottom margin settings through your software or by adjusting the top-of-form position. Adjusting the Loading Top-of-Form and Tear-off Positions with Micro Adjust To adjust the top-of-form or tear-off position, make sure paper is loaded in the printer.

Then hold down the Pause button for 3 seconds to enter Micro Adjust mode. When you are done, press Pause again to exit Micro Adjust mode.